Showing 73–90 of 123 results
High-Power 600W 10A 4V-60V MOS Tube FET Trigger Drive Module PWM Control High / Low Level Trigger Switch DC
Specifications:
- Operating voltage: DC 4V - 60V
- Trigger source: high level trigger (DC3.0V - 24V), low level trigger (DC 0.0V ~ 0.6V), switch control, can connect MCU IO port, PLC interface, DC power supply, etc. PWM signal, support signal frequency range of 0 - 2.5KHZ
- Output capacity: DC 4V - 60V, continuous current 10A at room temperature, power 600W! Auxiliary cooling conditions, the current up to 15A
- Life: unlimited switch
- Working temperature: -40-85 °
- Size: 3.4 * 1.7 * 1.2cm
HobbyKing Red Brick 100A ESC 5V UBEC
Hobbywing Quicrun WP Brushed Electronic Speed Controller For Rock Crawlers ESC 80A
IC L293D
JK2M2283 2 Phase 150V-220V AC 8A 110mm 130mm NEMA42/52 Motor StepperEngine Driver
JKBLD120 Brushless DC Motor Driver
JKBLD300 Brushless DC Motor Driver
Specifications:
- Brand Name: Jkongmotor
- Model Name: JKBLD300
- Type: BLDC motor driver
- Power: 300W
- Environment temperature: -10℃—50℃
- Input Voltage: +18—+50VDC
- Output Current: 15A—35A
- Suitable Motor Speed: 0-20000Rpm
- Hall Sensor Voltage: 4.5V—5.5V
- External Potentiometer: 10kΩ
- Support Motor: Brushless DC Motor less of 300w
JKBLD750 Brushless DC Motor Driver
JKD2060H Stepper Motor Driver
JKD5056S Stepper Motor Driver
Kangaroo X2 Motion Controller
Specifications:
- 2 channel self-tuning PID controller
- Position or speed control
- Quadrature encoder feedback or potentiometer feedback
- 80,000 pulses/sec processing
- Support for limit switches and mechanical stops
- Analog, R/C and serial inputs
L293D Motor Driver Board for ESP8266 WiFi NodeMcu Lua ESP12E
Specification
- ESP8266 WiFi Motor Drive Expansion Shield Board For NodeMCU ESP-12E
- Motor power supply (VM): 4.5V ~ 36V, can be powered separately
- Control power (VIN): 4.5V ~ 9V (10VMAX), can be powered separately
- Module provides short-circuit sub (short the VM and VIN), you can easily use one power (must be 4.5V ~ 9V) while completing motor drive and control.
- Logic Operating current Iss: ≤60mA (Vi = L), ≤22mA (Vi = H)
- Drive part of the work current Io: ≤1.2A
L293D Motor Driver Module 4.5-25V
L293D Motor Driver/Servo Shield for Arduino
Specifications:
- 2 connections for 5V ‘hobby’ servos connected to the Arduino’s high-resolution dedicated timer
- 4 H-Bridges: L293D chipset provides 0.6A per bridge (1.2A peak) with thermal shutdown protection, internal kickback protection diodes.
- Can run motors on 4.5VDC to 25VDC.
- Up to 4 bi-directional DC motors with individual 8-bit speed selection (so, about 0.5% resolution)
- Up to 2 stepper motors (unipolar or bipolar) with single coil, double coil, or interleaved stepping.
- Pull-down resistors keep motors disabled during power-up
- Big terminal block connectors to easily hook up wires (18-26AWG) and power
- Arduino reset button brought up top
- 2-pin terminal block and jumper to connect external power, for separate logic/motor supplies
- Tested compatible with Arduino Mega 1280 & 2560, Diecimila, Duemilanove, and UNO
L298N Dual H Bridge DC/Stepper Motor Driver Controller Module
L298N Motor Driver Module
L9110 L9110S DC Stepper Motor Driver Board HBridge
