Features:

1. Support 24 EEPROM and 25 SPI flash 8pin or 16pin chip
2. With 24/25 status indicator lamp
3. Support USB to TTL conversion support 24EEPROM and 25 SPI flash 8pin/ 16pin chip
4. Recognize 25 series chip automatically
5. Supports download STC series procedure of single chip
6. SPI pin to support expanding the utility
7. STC microcontroller supports a full range of program download
8. Support expanding the utility by SPI pin
9. With SOP8 SOP16 to DIP8 converter board
10. Supports Windows XP, Vista, Win7 and Win8 (32/64bit) system
11. Provide 5V-3.3V power supply output

Features :

1. Input Supply voltage: 5V
2. Input Supply Current: 5 mA
3. Communication Rate: 1 Mbps
4. Support CAN V2.0B technical standard, communication rate 1Mb / S.
5. 0 to 8 bytes long data field.
6. Use High-speed CAN transceiver TJA1050
7. SPI control for expanding Multi CAN bus interface
8. Use serial port could view the communication data
9. With the independent key, LED indicator, Power indicator
10. With power pin
11. Positioning screw hole center spacing 23 mm x 38 mm
12. The working current: typical 5mA, standby current 1 microamp. Except for the power indicator.

Features : 

1. Adopt imported controller PL2303HX, which can stabilize the flash with high speed
2. 500mA self-recovery fuse for protection.
3. Two data transmission indicator can monitor data transfer status in real time.
4. Reserve 3.3V and 5V pin interface, easy for the DDWRT of different voltage system that needs power.
5. The entire board is coated by the high quality transparent heat-shrinkable sleeve, making the PCB in insulation state from outside.
6. The electrostatic package ensures the board will not be damaged before use.
7. Support WIN7 system.

Features :

1. Automatic detection of data transfer speeds up to 1Mbps
2. Data exchange capability with an external interface with UART protocol
3. Output Voltage 5v and 3.3v Indicator LEDs USB Connector
4. With RX and TX Indicator LEDs
5. Manage System for Reducing Flow In Idle and Standby Mode
6. Support for serial output devices such as modems, card reader devices, digital cameras and more.
7. Interface: Mini USB
8. +3.3V and +5.0V signal Level Support using SMD jumper.
9. Supports Windows 8, Windows 7,  Windows Vista, Windows XP, Linux, Mac OS X, Windows CE 4.2-5.2, Windows CE 6.0

Features:

1. Operating Voltage: 1.5～5V JTAG IO Voltage.
2. System configuration: Windows XP, Windows Vista, Windows7, USB interface.
3. Stably support SignalTap II embedded logic analyzer function, no mistake while crawling data.
4. Fully support all Altera products such as CPLD: MAX3000, MAX7000, MAX9000 and MAXII.
5. FPGA: Stratix, StratixII, StratxIII, Cyclone, CycloneII, CycloneIII, ACEX1K, APEX20K and FLEX10K etc.
6. Active serial configuration device: EPCS1, EPCS4, EPCS16, EPCS64 etc.
7. Enhanced configuration devices: EPC1, EPC4.
8. Supports 3 download mode: AS, PS and JTAG.

• RED Wire – Power 5V, 500mA
• BLACK Wire – Ground
• WHITE Wire – RX
• GREEN Wire – TX

Features:

Features:

1. Working voltage: 4.5V – 5.5V (Onboard 3.3v LDO Regulator)
2. Working current: 300mA (LDO regulator can supply)
3. Driver Chip: CH340G
4. Supports all basic windows versions.
5. The adapter plate integrated 1000μF solid capacitors to ensure the current supply
6. The power supply will not be a problem to make WIFI module crashes unresponsive.
7. Using 3225 SMD crystal oscillator, improve the stability of serial work, on a beautiful and tall.