Specification:

• Input supply voltage: DC 12V-40V
• The maximum output power: 400W
• The maximum continuous output current:8A
• Static Current:0.02 A ( Standby )
• PWM frequency: 13kHz
• Duty Cycle adjustable: 10%-100%

Features:

• Bi-directional control for dual brushed DC motor.
• Support motor voltage from 7V to 35VDC.
• Maximum current up to 80A peak (1 second), 30A continuous, each channel.
• On board MOSFETs are switched at 18 KHz for quiet operation.
• Regenerative Braking.

Specifications:

• 32A continuous, 64A peak per channel
• 6-30V nominal, 33.6V absolute maximum
• Synchronous regenerative drive
• Ultrasonic 30 kHz switching frequency
• Thermal and overcurrent protection
• Battery protection mode
• USB control and monitoring
• USB serial converter mode for Kangaroo x2
• Configurable current limiting
• Custom user modes
• 12-bit motor outputs
• Input modes: analog, R/C, serial (plain text or packetized), USB
• Power outputs can act as voltage clamps, brakes, or be controllable
• Size: 2.75” x 3.5” x 1.0”    ||    70 x 90 x 25 mm

Specifications:

• DC Brush motor Driver, not for brushless motor
• Input Voltage (Motor): 7 – 45VDC
• Single power operation, just connect power to battery input.
• Dual Channels, it can drives two brush motor independently, or mixed.
• Regenerative Braking.
• Operating modes: RC (RC servo signal), Analog, PWM, simplified and packetized UART.
• Support Signed magnitude and Locked Anti-phase in PWM mode.
• Top cover comes with two DC brushless fans to cool the driver.
• Two manual/test buttons for each channel.
• Two output indicator LEDs for each channel.

Specifications: 

• 60A continuous, 120A peak per channel
• 6-30V nominal, 33.6V absolute maximum
• Synchronous regenerative drive
• Ultra-sonic switching frequency
• Thermal and overcurrent protection
• Lithium protection mode
• Input modes: Analog, R/C, simplified serial, packetized serial
• Size: 3” x 3.5” x 1.8”     ||  76 x 89 x 46 mm

Specifications:

1. Bidirectional control for one brushed DC motor.
2. Operating Voltage: DC 6V to 30V
3. Maximum Motor Current: 20A continuous, 60A peak
4. Buttons for quick testing.
5. LEDs for motor output state.
6. Overcurrent protection with active current limiting.
7. Temperature protection.
8. Undervoltage shutdown.

Features:

• Bi-directional control for two brushed DC motors.
• Support motor voltage ranges from 5V to 30VDC (Rev2.0).
• No Reverse Polarity Protection at Vmotor, please double check the polarity before power up.
• Maximum current up to 10A continuous and 30A peak (10 seconds) for each channel.
• Support 3.3V and 5V logic level input (for PWM and DIR), compatible with Arduino and Raspberry Pi.
• Solid state components provide faster response time and eliminate the wear and tear of mechanical relay.
• Full NMOS H-Bridge for better efficiency and no heat sink is required.
• Regenerative Braking.
• Speed control PWM frequency up to 20KHz (output frequancy is same and input frequancy).
• Support both Locked-Antiphase and Sign-Magnitude PWM operation. ** Note this is not “RC PWM”
• 2 activation buttons for manual activation or fast test on each channel.
• Dimension: 84.5mm x 62mm

Please Note: If this material is not available in our stock, we will arrange & ship it in 3 working days if still we unable to proceed; we will refund 100% of your payment. 

QUICK OVERVIEW :

1. Single power operation.
2. Dual Channels means it can drive two brush motor indepently ,or mixed.
3. Support Signed magnitude and Locked Anti-phase in PWM mode.
4. Two manual/test buttons for each channel.
5. Power, Error indicator, RUN status (Left and Right) LEDs
6. On board reset button to restart the MCU after changing operation mode.
7. Operating modes: RC (RC servo signal), Analog, PWM, simplified and packetized UART.