Showing 1–18 of 56 results
1.5Amp 7V-25V DC Motor Driver (4 Channels)
Features:
- Bidirectional control for four (4) brushed DC motors.
- Operating Voltage: DC 7V to 25V
- Maximum Motor Current: 1.5A continuous, 2.5A peak
- Buttons for quick testing.
- LEDs for motor output state.
- PWM and DIR inputs.
- Inputs compatible with 3.3V and 5V logic (Arduino, Raspberry Pi, PLC, etc).
- Reverse polarity protection.
- Board size: 10.67cm x 5.21cm
1203B PWM 6V 12V 24V 28V 3A DC Motor Speed Regulator
12V-24V 8A Adjustable Dimmer Switch For Single LED Strip
12V-40V 10A DC Motor PWM Speed Control Switch Governor
170W High Power H-Bridge Motor Driver Module For NMOS Brake Duty Cycle For DC 5-40V Motor 4 External NMOS Tubes Two PWM Inputs
Specifications:
- With full bridge driver chip + low resistance 55V110ANMOS, the motor can be turned forward and backward.
- Two PWM inputs, dutycycle regulated in 0-100%. Instant braking ability.
- The working voltage is 10-40V and the power is below 170W
- The control is simple and convenient. Only 3 input lines are needed to control the motor
- Chip built-in dead time hardware control, more suitable for frequent reversing. Reduce the loss of the pipe itself.
- Tin plating on the back of the module. A conductor can flow through a larger current.
- Support 5V, 3..3V logical input. Suitable for all types of single-chip IO port direct control. You can also control the positive and negative rotation of the motor by analog input.
- Board size: 38.8*67.5mm
2000W DC 9V-55V 40A Motor Speed Controller Electric PWM Speed Control Regulator
2000W DC 9V-55V 40A Motor Speed Controller Electric PWM Speed Control Regulator with Reversible Switch
20A Brushed Electronic Speed Controller
20A PWM DC Motor Speed Regulator Module (9V, 12V, 24V, 36V, 48V, 60V)
Features :
- Adjustable speed range: 0%-100%.
- Speed adjustment way: Potentiometer.
- Output voltage: Linear under load.
- Speed control type: Basins.
- Output voltage: Load Linear
- Type: Adjusting flow
- The motor running condition adjustment: Forward / Stop / Reverse
- Reverse polarity protection: Yes.
- Suitable Motor: DC brush motors.
2×30 Cytron SmartDrive MDDS30 (80A Peak)
2×32 Sabertooth Motor Driver
Specifications:
- 32A continuous, 64A peak per channel
- 6-30V nominal, 33.6V absolute maximum
- Synchronous regenerative drive
- Ultrasonic 30 kHz switching frequency
- Thermal and overcurrent protection
- Battery protection mode
- USB control and monitoring
- USB serial converter mode for Kangaroo x2
- Configurable current limiting
- Custom user modes
- 12-bit motor outputs
- Input modes: analog, R/C, serial (plain text or packetized), USB
- Power outputs can act as voltage clamps, brakes, or be controllable
- Size: 2.75” x 3.5” x 1.0” || 70 x 90 x 25 mm
2×5 Sabertooth Motor Driver for R/C
Specifications:
- Weight: 18g / 0.6oz
- Input Voltage: 6V to 18V, 6-12 cell NiMH or NiCd, 2s-4s LiPo, 6V or 12V lead acid (not 18+V lead acid!)
- 5A continuous per channel, 10A peak
- Synchronous regenerative drive
- Ultra-sonic switching frequency
- Thermal and overcurrent protection
- Lithium protection mode
- Size: 1.8” x 1.6 ” x .5” || 45 x 40 x 13 mm
- 5" / 13cm servo pigtails
2×60 Cytron 7V-45V SmartDrive DC Motor Driver (100Amp Peak)
Specifications:
-
DC Brush motor Driver, not for brushless motor
-
Input Voltage (Motor): 7 - 45VDC
-
Single power operation, just connect power to battery input.
-
Dual Channels, it can drives two brush motor independently, or mixed.
-
Regenerative Braking.
-
Operating modes: RC (RC servo signal), Analog, PWM, simplified and packetized UART.
-
Support Signed magnitude and Locked Anti-phase in PWM mode.
-
Top cover comes with two DC brushless fans to cool the driver.
-
Two manual/test buttons for each channel.
-
Two output indicator LEDs for each channel.
2×60 Sabertooth Motor Driver
Specifications:
- 60A continuous, 120A peak per channel
- 6-30V nominal, 33.6V absolute maximum
- Synchronous regenerative drive
- Ultra-sonic switching frequency
- Thermal and overcurrent protection
- Lithium protection mode
- Input modes: Analog, R/C, simplified serial, packetized serial
- Size: 3” x 3.5” x 1.8” || 76 x 89 x 46 mm
3V 6V 12V 24V 35V PWM DC Motor Speed Regulator
5-36v Switch Drive High-power MOSFET Trigger Module
5A PWM Speed Control Forward Reverse 5V 12V 24V DC Motor Driver Servo Motor Drive Board H Bridge Motor Driver Module
Specifications:
- Product model: YYH-LWZ
- Input voltage: DC DC5V~27V
- Rated output current: 5A, can maintain continuous current within 5A
- Static standby current: only about 3MA
- Signal type: The control signal uses the sink current drive method, which supports the direct drive of most single-chip microcomputers, the optocoupler is completely isolated, and the PWM signal frequency supports within 20KHZ
- Use fast recovery diodes to prevent excessive anti-induced electromotive force from burning out the control part when the motor starts
60A High Power MOS Dual Channel H-bridge DC Motor Driver Module
Features:
- Use SMT, high integration, superior layout design, very beautiful, small size, built-in 2 channel high power DC motor drive, drive module size only 70mm * 56 mm.
- Wide heat sink in the large current may be effective for drive module heat, keep good stable Performance.
- The module maximum rated current 60A, and the on resistance only 0.003 ohms.
- Switch frequency is high, the most accessible 60KHZ, so effective to debug motor.
- Control interface is very simple: A1, A2 = 0.0 for brake; A1, A2 = 1.0 for forward; A1, A2 = 0.1 for Reverse.PA for PWM wave input (motor speed regulation); G for common Ground (B channel for the same control).
- All MCU of 3.3 V and 5 V are can control this module, and only need one channel motor power supply (12 V ~ 48V).