Telephone Enquiry: 9322763532 / 7039508982

Cart

ALL CATEGORIES
More Categories Less Categories

Cart

2×30 Cytron SmartDrive MDDS30 (80A Peak)

5,490.00 (Including GST)

4,652.54 ( + 837.46 GST)

Features:

  • Bi-directional control for dual brushed DC motor.
  • Support motor voltage from 7V to 35VDC.
  • Maximum current up to 80A peak (1 second), 30A continuous, each channel.
  • On board MOSFETs are switched at 18 KHz for quiet operation.
  • Regenerative Braking.

Available on backorder

Purchase this product now and earn 47 Points!

Compare
SKU: RDNA-A4.23 Category:

Share this product

Description

We know DC brushed motor is widely used for many different applications; from conveyor, AGV (Automated Guide Vehicle), mobile robot and combat robot. One of the reasons is the ease to use it, just connect the two terminals of motor to power respectively, it will start rotating, so simple. Yet, to control the speed and direction from a controller, a motor driver is needed.

This is SmartDriveDuo-30, with the ease of accepting RC (Radio Control) signal to drive two DC brushed motors in independent or mix mode, it is perfect for combat robot. Not to forget it supports up to 80Amps of peak current (1 second) and 30Amps continuous current at each channel, best for medium power motor.

Features:

  • Bi-directional control for dual brushed DC motor.
  • Support motor voltage from 7V to 35VDC.
  • Maximum current up to 80A peak (1 second), 30A continuous, each channel.
  • On board MOSFETs are switched at 18 KHz for quiet operation.
  • Regenerative Braking.
  • On board Error LEDs to indicate: (each channel)
    • Input Error (Blinks 2 times)
    • Under Voltage Warning (Blinks 3 times)
    • Over Voltage Protection (Blinks 4 times)
    • Over Temperature Protection (Blinks 5 times)
  • Thermal protection.
  • Current limit protection.
  • Multiple input modes:
    • RC (Radio Control)
    • Analog voltage from potentiometer/variable resistor/joystick
    • PWM and DIR (sign-magnitude and locked-antiphase) from microcontroller
    • Serial Simplified or Serial Packetized from microcontroller
  • GROVE compatible connectors for control input.
  • RC (Radio Control) friendly connectors.
  • On board push buttons for fast test and manual operation.
  • On board LED indicators for Error, RUN, Over current, motor output, for each channel.
  • NO POLARITY PROTECTION FOR V MOTOR.
  • Dimension: 81.28mm(W) x 101.60mm (L) x 42mm (H)

 

And with that, it is smart enough to accept control signal from:

RC (Radio Control)
PWM of microcontroller
Analog voltage of Potentiometer/Variable Resistor/Joystick
UART data of microcontroller

The operation mode is determined by the configuration on DIP switch, please do refer the User’s Manual for detailed settings. Not to forget, to make it RC receiver friendly, we have added 2×3 header pin, with just 2 x RC extension cable(which is included), the wiring is done, it takes only 2 minutes! And by default, MDDS30 is configured in RC controller, Mixed control mode, even easier!

With MDDS30’s wide operating voltage range, you can now series up two SLA battery to power your motor as it supports up to 35VDC input. And you only require one power input to operate the motor and driver. Don’t worry, 3-cell and 6-cell Li-po battery are within the operating voltage 🙂 Hey! It also comes with battery low voltage warning, what else do you need?

Which motor is good to be driven by MDDS30? As long as the motor:

Is DC Brush motor (Two Terminals)
Operating voltage from 7V to 35VDC
Rated Current <= 30A
Peak Current <= 80A

Documents:

Tutorials:

Packing List:

Reviews

There are no reviews yet.

Only logged in customers who have purchased this product may leave a review.