Showing 73–90 of 105 results
SPI to Ethernet Hardware TCP/IP W5500 Ethernet Network Module
Specifications:
- Chip type: W5500
- Supports both 3.3V & 5V
- Hardwired TCP/IP Protocols: TCP, UDP, ICMP, IPv4, ARP, IGMP, PPPoE
- 10BaseT/100BaseTX Ethernet PHY embedded
- Supports automatic response (full duplex/half duplex mode)
- Supports 8 independent sockets simultaneously
- Internal 32Kbytes Memory for Tx/Rx Buffers
ST Link V2 Programmer For STM8 and STM32
Specifications:
- PCB installed inside of aluminum alloy U disk shell, portable, safe and reliable!
- Interface definition directly marked on the shell, clear, convenient and practical!
- 5V, 3.3V offers at the same time, allowing you to program your target board with both 5V and 3.3V
- Shell characters using laser engraving, never fade off! Permanent clarity!
- 500MA internal resettable fuse, complete protection of your expensive computer motherboard!
- SWIM cable for connection to the application via a pin header or a 2.54 mm pitch connector
- SWIM programming speed rate: 9.7 Kbytes/s in low speed and 12.8 Kbytes/s in high speed
ST-LINK/V2 in-circuit debugger/programmer for STM8 and STM32
TJA1050 CAN Controller Bus Driver Interface Module
Features :
- Onboard TJA1050 CAN controller interface chip
- Chip commonly used pin has led, convenient connection to use
- Pin 5 v to the power supply
- PCB board size: 22 (mm) x11.5 (mm)
- Fully compatible with the ISO 11898 standard
- High speed (up to 1 Mbaud)
- Very low Electro-Magnetic Emission (EME)
- Differential receiver with wide common-mode range for high Electro-Magnetic Immunity (EMI)
- An unpowered node does not disturb the bus lines
- Transmit Data (TXD) dominant time-out function
- A silent mode in which the transmitter is disabled
- Bus pins protected against transients in an automotive environment
- Input levels compatible with 3.3 V and 5 V devices
- Thermally protected
- Short-circuit proof to the battery and to ground
TTL FTDI Transmitter USB For 3.3V/5V Dual power FT232RL MWC Programmer
Features :
- Automatic detection of data transfer speeds up to 1Mbps
- Data exchange capability with an external interface with UART protocol
- Output Voltage 5v and 3.3v Indicator LEDs USB Connector
- With RX and TX Indicator LEDs
- Manage System for Reducing Flow In Idle and Standby Mode
- Support for serial output devices such as modems, card reader devices, digital cameras and more.
- Interface: Mini USB
- +3.3V and +5.0V signal Level Support using SMD jumper.
- Supports Windows 8, Windows 7,  Windows Vista, Windows XP, Linux, Mac OS X, Windows CE 4.2-5.2, Windows CE 6.0
TTL to RS485 Power Supply Converter Board 3.3V 5V Hardware Auto Control Module
Specifications:-
- Operating Voltage (VDC):3 ~ 30
- Compatible Signals:3.3V and 5.0V
- Working Temperature Range (°C):-40 to 85
- Baud Rate:110 to 256000bps
- Support multi-machine communication, at least 40 nodes can be connected to the same network
- can be hot-swapped and there will be no signal thrombosis.
- With standard 2.54 pitch pin headers
TXS0108E High Speed Full Duplex 8 Channel Logic Level Converter
Specifications:
- It can provide 3.3-5V, 1.8-3.3V level conversion.
- PCB Color: Blue.
- 8-bit bi-directional 3.3V-5V/5V-3.3V logic level converter board.
- Serial communication interface compatible with UART/IIC/SPI port easily to connect.
- Ship out by USPS with tracking information and 7-17 days delivery time usually.
- Widely used in the MCU and SD card, MCU and serial devices, MCU and 5V/3V module communication.
USB 3.0 to VGA Converter
USB ASP AVR Programmer
Features :
- Model No : USB ASP AVR Programming Device for ATMEL Processors
- Compatible Chips:
- ATMega Series
- Tiny Series
- Classic Series
- CAN Series
- PWM Series
USB AVRISP mkII XPII Supports AVR Studio 4&5&6&7
Features:
- Supports all AVR devices with ISP or PDI interface, and certain 51 Devices
- Programs both Flash and EEPROM
- Supports Fuses and Lock Bit Programming
- Based on AT AVRISP mkII firmware
- Upgradable to support future devices
- Adjustable ISP programming speed up to 8M frequency
- USB 2.0 compliant (full speed, 12Mbps)
- 3 optional cables to the target board
- Powered from a USB bus, does not require an external power supply
USB Blaster ALTERA CPLD/FPGA Programmer
Features:
- Operating Voltage: 1.5～5V JTAG IO Voltage.
- System configuration: Windows XP, Windows Vista, Windows7, USB interface.
- Stably support SignalTap II embedded logic analyzer function, no mistake while crawling data.
- Fully support all Altera products such as CPLD: MAX3000, MAX7000, MAX9000 and MAXII.
- FPGA: Stratix, StratixII, StratxIII, Cyclone, CycloneII, CycloneIII, ACEX1K, APEX20K and FLEX10K etc.
- Active serial configuration device: EPCS1, EPCS4, EPCS16, EPCS64 etc.
- Enhanced configuration devices: EPC1, EPC4.
- Supports 3 download mode: AS, PS and JTAG.
USB To 8 Pin RS-422 SC09-FX PLC Programming Cable
Specifications:
- PLC Programming Cable USB-SC09-FX is a direct replacement for the USB version of MELSEC FX Series PLC.
- Suitable for Mitsubishi MELSEC
- 8-pin DIN connector.
- They are designed for computers without a serial port.
- Condition: New
- Cable length:3 meters
- The quality is guaranteed. It's tested before shipment.
USB to RS485 12-24V Industrial Converter Module
USB to RS485 Converter Adapter Support WIN7 XP Vista Linux Mac OS
Specifications:
- USB to RS485 Converter Adapter
- USB connector: to your PC
- RS485 connector: to your RS485 device
- Fully compliant USB 2.0 standard, backward compatible with USB1.1
- Support System: Windows XP, Vista, Windows 7, Linux, MacOS, and WinCE5.0 drive
- Supports Plug, Play and hot-swap ( USB side)
- Better than using CH341D chip or similar chip to support the laptop USB port
- Communication distance up to 1.2KM, with the anti-jamming performance of the industrial site
- No need external power, powered by USB port
USB to Serial Converter CA-US9 (COM Port)
USB to TTL PL2303 PL2303HX Cable 4Pin
Specifications:
- Data transfer rates from 300 baud to 3Mbaud at TTL levels.
- Supports RS485 and RS232.
- Single-chip USB to UART conversion.
- No additional firmware programming required.
- Receive and Transmit LED drive signals.
- USB2.0 full speed compatible.
- Low USB bandwidth consumption.
- Internal EEPROM with user-writable area.
- Output can be directly connected to microcontroller UART or I/O.
- Entire USB protocol handled by the electronics in the cable.
- Integrated power-on-reset circuit.
- UART signal inversion option.
- True 5V/3.3V/2.8V/1.8V CMOS drive output and TTL input.
- Operating temperature range: -40ºC to +85ºC.
- 128 byte receive buffer and 256 bytes transmit buffer, utilizing buffer smoothing technology to allow for high data throughput.
- Cable length up to 1 meter.
- FCC and CE are compliant.