Showing 1–24 of 48 results
2 Channel Logic Level Converter 3.3V 5V TTL
4-20mA to 5V Converter for Arduino Industrial Sensor Interface Board
Adapter Breakout Board for ESP-32f ESP32 ESP-Wroom-32 Wireless Bluetooth Module
AMS1117-3.3 LDO 800MA DC 5V to 3.3V Step-Down Power Supply Module
AVR ISP 10 Pin to 6 Pin Adapter Board
Breakout Board PS2 Connector
Capacitor Touch Dimmer, Constant Voltage LED Stepless Dimming, PWM Control Board
Specifications:
- Power supply voltage(VCC): 2.0, 3, 5.5 V.
- Output high VOH: 0.8VCC V
- Output low VOL: 0.3VCC V
- Response time (touch mode) : 60 mS
- Output Pin Sink Current (@ VCC = 3V, VOL = 0.6V) : 8 mA
- Output pin pull-up current (@ VCC = 3V, VOH = 2.4V) : 4 mA
- Response time (low power mode) : 220 mS
- Size : 24 x 24 x 7.2 mm
CD74HC4067 High Speed CMOS 16-Channel Analog/Digital Multiplexer Breakout Module
CJMCU MCP4725 I2C DAC Breakout Development Board
CJMCU-1286 PIC16F1823 Microcontroller Development Board
CJMCU-2551 MCP2551 CAN Protocol Controller High-speed Interface Module
Features:
- Supports 1 Mb/s operation
- Suitable for 12V and 24V systems
- The externally-controlled slope for reduced RFI emissions
- Detection of ground fault (permanent Dominant) on TXD input
- Power-on Reset and voltage brown-out protection
- An unpowered node or brown-out event will not disturb the CAN bus
- Low current standby operation
- Protection against damage due to short-circuit conditions (positive or negative battery voltage)
- Protection against high-voltage transients
- Automatic thermal shutdown protection
- Up to 112 nodes can be connected
- High-noise immunity due to differential bus implementation
- Temperature ranges: – Industrial (I): -40°C to +85°C – Extended (E): -40°C to +125°C
CJMCU-TRRS 3.5mm Jack AV Stereo Module
Specifications :
- Mini design, portable and easy to use.
- It is the audio-style connectors that you see on some phones, MP3 players, and development boards.
- TRRS stands for “Tip, Ring, Ring, Sleeve,” which reflects the fact that, unlike a standard stereo connector, this actually has three conductors and a ground.
- Some devices use the extra conductor for a microphone (like hands-free headsets) or to carry a video signal (like in some MP3/MP4 players).
CP2112 debug board USB to I2C Communication Module
Features:
- On-chip power-on reset circuit, on-chip voltage regulator: 3.45 V output
- Compliant with USB specification 2.0 standard; full speed (12Mbps)
- USB suspend status via SUSPEND and /SUSPEND pins
- Integrated 194-byte one-time programmable ROM for storing customizable product information
- 512-byte SMBus data buffer, configurable clock speed device address 7-bit value is the slave address of CP2112
- Windows, Mac, and Linux HID to SMBus libraries API for rapid application development, open-access interface specifications.
- 8 GPIOs can be configured as input/output and open-drain/push-pull, configurable clock output for external devices 48MHz to 94kHz, switching LEDs during read/write SMBus
- Module size: 29.5mm*21.3mm, with two M3 mounting holes, one MicroUSB female port
- Application areas: Portable controllers, USB dongle, data logging
DB25-M2 DB25 to Terminal with Nut (Female DB25)
DB25-M2 DB25 to Terminal with Nut (male DB25)
DB9 Female Screw Terminal to RS232 RS485 Conversion Board
Features :
- Brings all 9 pins of a DB9 connector to screw terminal blocks
- Adapter used for communication debug
- 9 pcs signal line was all lead out, name and number clearly labelled
- All-copper DR9 seat, anti-oxidation, better contact
- Military board, three anti-paint sprays an entire board, corrosion-resistant
- Terminal spacing 3.96MM, screw hole diameter 2MM, need to use a width of 2MM screwdriver for assembly;
- Use of environmentally friendly copper terminals, through IS0-9001
DB9 Female Terminal to RS232/RS485 Serial Conversion Board
DB9 Female to DB9 Female Angular Connector
DB9 Female to DB9 Male Angular Connector
DB9 Male Screw Terminal to RS232 RS485 Conversion Board
Features :
- Brings all 9 pins of a DB9 connector to screw terminal blocks
- Adapter used for communication debug
- 9 pcs signal line was all lead out, name and number clearly labelled;
- All-copper DR9 seat, anti-oxidation, better contact;
- Military board, three anti-paint sprays an entire board, corrosion-resistant;
- Terminal spacing 3.96MM, screw hole diameter 2MM, need to use a width of 2MM screwdriver for assembly;
- Use of environmentally friendly copper terminals, through IS0-9001.
DB9 Male Terminal to RS232/RS485 Conversion Board
DC 3-5V X9C103S Digital Potentiometer Board Module for Arduino
Features:
- Supply voltage: 3V-5V
- Chip: X9C103S
- Dimensions : 28 x 14 x 4 (LxWxH) mm.
- 10K span potentiometer.
- Potentiometer center tap between the 0-10k slide in total 100
- VL and VH digital potentiometer sliding rheostat port corresponding to the low-end and high-end, allowing the input voltage range -5V to + 5V.
