Showing 577–585 of 585 results
LiPo Battery Voltage Checker 1S-8S with Buzzer
FlySky FS-i6 2.4G 6CH PPM RC Transmitter With FS-iA6B Receiver
128×64 LCD Blue
Specifications:
- Operating Voltage: 5V
- Viewing angle: 6 ‘o’ clock
- MCU I/F: Serial or 8-bit parallel
- Display Color: Blue
- Low power consumption
- Automatic power-on Reset
- Graphic and Character mix modes display
- Display Construction: 128*64 dots
- Display Mode: STN
- Type: Chip On Board (COB)
- Interface: 6800 8-bit Parallel
- Display Type: Positive Transflective
- Backlight: LED Blue/ 5.0V
128×64 LCD Green/Yellow
Dot Matrix MAX 7219 Single Module
Specifications:
- Voltage Supply (Vs):4.0V ~ 5.5V
- Â Supply current:330mA
- Â Segment drive source current:10mA
- Â Shut down current:150uA
- Â Scan rate:500-1300Hz, 800Hz
- Operating temperature (MAX7219E):40°C ~ 85°C
- Dimension 32 x 32 x 1.5 cm (L x W x H) (Single Module)
- Dot Led Matrix Module incorporating MAX7219 Driver chip
- Requires only 3 communication wires of MCU
- Cascading multiple Matrix LED Module is very easy
- The size of the display is very compact
- The PCB features M3 holes for mounting.
- Compatible With Arduino Board, Raspberry pi
IIC/I2C Serial Interface Adapter Module – Compatible with 1602 LCD & 2004 LCD
Specifications:
- IC Chip:Â PCF8574
- Power Supply: 5V
- Serial I2C control of LCD display using PCF8574
- Backlight can be enabled or disabled via a jumper on the board.
- Contrast control via a potentiometer.
- Can have 8 modules on a single I2C bus (change address via solder jumpers) address, allowing
- Size: 41.6 x 19.2 mm
- Compatible with Arduino Boards, Raspberry piÂ
16×2 LCD Blue with I2C Module (Soldered)
Specifications:
- Compatible with Arduino/Genuino UNO, Leonardo, Mega, 101 (Intel Curie), Micro, Nano, Mini
- I2C Address:0x20-0x27(0x20 default)
- Back lit (Blue with white char color)
- Supply voltage: 5V
- Interface:I2C/TWI x1,Gadgeteer interface x2
- Adjustable contrast
- Size: 80x36x20mmz(3.1x1.4x0.7in)
RASBERRY PI 3 B+ BCM2837B0 SoC, IoT, PoE Enabled
Specification
- Model : Raspberry Pi 3 Model B+
- Processor : Broadcom BCM2837B0, Cortex-A53 (ARMv8) 64-bit SoC @ 1.4GHz
- RAM:1GB LPDDR2
- Connectivity : Gigabit Ethernet over USB 2.0
- Operating Power : 5V/2.5A DC
- GPIO : Standard 40-pin GPIO Header
- Video and Sound : 2-Lane MIPI DSI Display Port
- Clock Speed:1.4 GHz
- On Board Ports : 15-pin MIPI Camera Serial Interface (CSI-2), 4 x USB 2.0 Connector, 4-
- pole stereo output and composite video port, 40-pin 2.54 mm (2×20 strip) GPIO, Full-size
- HDMI Output Port
- Micro-SD Card Slot : Yes (FAT32 format), support maximum 32G Micro SD Card
- Operating Temperature Range (°C):-10 to 60
- Weight (gm):44
- Length (mm):85
- Width (mm):56
- Height (mm):23
- HDMI Port : Full Size
- Shipping Weight :0.047 kg
- Shipping Dimensions:9 × 6 × 4 cm
2.4 inch Touch TFT LCD Arduino Shield With Pen
Specifications:
-
- 2.4″ diagonal Touch LCD TFT display
- 240×320 resolution, 18-bit (262,000) color
- 8-bit digital interface, plus 4 control lines
- Uses digital pins 5-13 and analog 0-3. That means you can use digital pins 2, 3, and analog 4 and 5. Pin 12 is available if not using the microSD
- Works with any Arduino UNO
- 5V compatible! Use with 3.3V or 5V logic
- 4 white LED backlights. By default but you can connect the transistor to a digital pin for backlight control
- Onboard 3.3V 300mA LDO regulator