CNC 4 Axis Controller DSP Controlled – TB6560 Stepper Motor

1. The inductive DC-DC stepdown module, computer terminal and then using the power isolation module design, just to run a set of power input, the input voltage of 24V-40V allows high voltage input, completely beyond TB6560, TB6560 of the input voltage. typically 24V.
2. Increase the external signal input optocoupler used in all optical coupling isolation input.
3. Increase the simulation 0-10V output, combined with MACH3 software to control the drive spindle speed.
4. add a select group of relay outputs (can output two relays, control the two different devices, load isolation, P9 pin relay 1, relay 2 pin P16, P17 cited relay 3 setting foot)
5. Increase the 20-pin multi-connector, docking can be a variety of signal input control (direct signal input with the handle or Weihong card), you can use the micro controller, ARM, DSP control.
6. Add the buffer chip signal, amplifies the external signal, increasing the accuracy of the pulse.
7. E-type bottom oversized aluminum heat sink to ensure the full capacity 24 hours, the temperature is very low (which can add a fan or other cooling device).

This driver board controller is a high performance microstepping driver board based on the latest original TOSHIBA high-efficiency TB6600HG IC. This driver board controlelr has upgraded their PCB board, the re-designing the PCB board will avoid the TB6600 chip on the board being easily blown as the previous version. The TB6600HG adopts single-chip PWM bipolar sinusoidal chopper to ensure the low vibration and high efficiency. Moreover, the brand new design with BiCD0.13 (45V) process technology on the chipset also ensures maximum 5.0A output current and 45V output withstand voltage. Consequently, as long as the current range of the stepper motor is within 0.2-5 amps, all the 2 Phase or 4 Phase of Nema17, Nema23, Nema24 stepper motors will work perfectly with this new-type TB6600HG Stepper Driver Board.

Suitable for any small-and-medium automatic equipment with CNC controller, such as X-Y-Z tables, labeling machines, laser cutters, engraving machines, and pick-place devices.

For advising, such as brand, architechture mould, badge, nameplate, display boards, doorplate, furniture decoration, etc..

For processing various pattern mould.

This kit is suitable for below typical CNC machines.

Dip Switch Settings

Microstep	SW1	SW2	SW3
N/A	ON	ON	ON
1(Full Step)	OFF	ON	ON
2	ON	OFF	ON
2	OFF	OFF	ON
4	ON	ON	OFF
8	OFF	ON	OFF
16	ON	OFF	OFF
N/A	OFF	OFF	OFF

Output Current	SW4	SW5	SW6
0.2A	ON	ON	ON
0.6A	OFF	ON	ON
1.2A	ON	OFF	ON
1.8A	OFF	OFF	ON
2.5A	ON	ON	OFF
3.3A	OFF	ON	OFF
4.2A	ON	OFF	OFF
5.0A	OFF	OFF	OFF

Power Supply Selection

Voltage Selection

12-24V DC power supply for Nema 17 stepper motors.

24-45V DC power supply for Nema 23/24 stepper motors.

(High (≥ 45V) voltage will burn out the chips or stepper motors!!! Please be careful in choosing power supply.)

Current Selection

Output current of the power supply can be calculated by the following formula.

Output current = Rated current of your stepper motors x quantity + 2A.

If the power of power supply is not big enough for the driver, it will easily burn the drivers.

Please SHUT DOWN the power before you plug or unplug the connectors to avoid burning up the board.

Connection Diagram For Reference

Electrical Specifications
Input Voltage	12V ~ 45V(Peak) DC
Output Current	0.2A ~ 5.0A (Peak)
Drive Type	Pulse + Direction + Enable Signal Control (Single-Chip PWM Bipolar Sine Chopper)
Suitable Motor	Nema17, Nema23, Nema24(Rated current: 0.2A-5.0A)
Operation Environment & Other Specifications
Cooling	Natural Cooling or Fan Forced cooling
Operating Environment	Environment Avoid dust, oil fog, corrosive gas Ambient Temperature 0 °C ~ 50°C (32°F ~ 122°F) Humidity 40%RH ~ 90%RH Operating Temperature 70°C (158°F) Max
Storage Temperature	-20 °C ~ 65°C (-4°F ~ 149°F)
Total Weight	Approx. 305g
Dimensions	173*113*78mm

1 x The 3rd Generation 4 Axis TB6600HG Stepper Driver Board

1 x LPT Parallel Cable

1 x CD

Package include:

1 x CNC 4 Axis Controller DSP Controlled – TB6560 Stepper Motor