Showing 1–12 of 18 results
Anti-Vibration Shock Absorber for APM/KK/MWC/PixHawk
APM 2.8 Flight Controller with Built in Compass
Specifications :
- Straight Needle
- Arduino Compatible!
- Onboard 4 MegaByte Dataflash chip for automatic data logging.
- Optional off-board GPS, a uBlox LEA-6H module with Compass.
- One of the first open source autopilot systems to use Invensense’s 6 DoF Accelerometer/Gyro MPU-6000.
- Barometric pressure sensor upgraded to MS5611-01BA03, from Measurement Specialties.
- Atmel’s ATMEGA2560 and ATMEGA32U-2 chips for processing and USB functions respectively.
CC3D OpenPilot EVO Flight Controller with Side Pins
Specifications :
- with a function of being directly plugged into the satellite receiver(It needn’t conversion cable)
- Powerful STM32 32-bit microcontroller running at 90MIPs with 128KB Flash and 20KB RAM.
- 3-axis high-performance MEMs gyros and 3-axis high-performance MEMs accelerometer.
- Tiny 36 x 36 mm 4 layer PCB for superior electrical noise reduction and flight performance.
- Software support for Windows, Mac, and Linux.
- Direct high-speed USB support with no drivers required, a true plug and play device.
- Spektrum satellite receiver support.
- Futaba S-BUS hardware support.
- Innovative Flexi-port technology for superior port flexibility.
- 4Mbits onboard EEPROM for configuration storage.
Damping Plate Shock Absorber for CC3D Flip32 Naze32 Mini APM Flight controller
DJI NAZA-M Lite V1.1 with GPS Kit
F3 Brushed Flight Control Board Based On SP RACING F3 EVO Brush for Micro FPV Frame
Specifications:
- Supported Receiver Input Signal: PPM, SBUS, DSM
- Support PPM, SBUS, DSM receiver input signal
- Battery voltage detection and buzzer interface
- Run on SP RACING F3 EVO firmware 32 brush flight control
- Large current NMOS transistors, operating current can reach 10A or higher
- Use STM32F303CCT6 + MPU6500, advanced hardware platform F3 for higher flight stability
Flysky FS-i6S 2.4GHz 10CH AFHDS 2A RC Transmitter With FS-iA10B 10CH Receiver
- FS-i6S Transmitter:Â
- No. of Channel: 10
- Frequency Range: 2.4055 – 2.475GHz
- Band Width: 500KHz
- Band Number: 140
- Transmitting Power: <20dbm
- 2.4G Mode:Â AFHDS 2A
- Modulation System: GFSK
- FS-iA10B Receiver:
- No. of Channel: 10
- Frequency Range: 2.4055 – 2.475GHz
- Band Number: 140
- Receiver Sensitivity: -105dbm
- 2.4G Mode:Â AFHDS 2A
- Modulation System: GFSK
KK2.1.5 Multi-rotor LCD Flight Control Board With 6050MPU And Atmel 644PA
Naze32 6DOF Flight Control board
OMNIBUS F4 V2 PRO Flight Controller with SD Card Slot & BEC
- Dimensions: 37 x 37 x 10 mm(L x H x W)
- Weight: 12 gm.
- SPI Gyro MPU6000
- MicroSD Blackbox
- F4 Processor (F405)
- 5v3a SBEC
- Built-in Current Sensor
- On-Board OSD (controlled by Beta flight, FC over SPI bus)
- On-Board Video Filter (only can supply 5V to VTX and Camera)
- On-Board Voltage Regulator and Power supply (BEC)
PDB-XT60 with BEC 5V and 12V
Specifications:
- 4-layers and 1.6mm PCB
- Built-in XT60 Socket
- Total 6 pairs ESC solder tabs are fit for H or X type frame
- 5V and 12V Output LED indicators
- Regulated 5V and 12V outputs
- BEC 5V output:Â 5V/2A (Max.2.5A 10s/minute)
- Output Ripple:Â 40mV (VIn= 16V, VOut= 5V@2A load)
- Short-circuit tolerant:Â 5 seconds/minute
- BEC 12V output (4S LiPoly, 13~18V DC):Â 12V/500mA (Max.0.8A 5s/minute)
- BEC 12V output (3S LiPoly): =3S LiPoly voltage – 1V
