CJMCU TCA9548A I2C 8 Channel Multiple Extensions Development Board 01

Click to enlarge

CJMCU TCA9548A I2C 8 Channel Multiple Extensions Development Board

Features :

Low Standby Current.
1-to-8 Bidirectional Translating Switches.
I2C Bus and SMBus Compatible.
5-V Tolerant Inputs.
Latch-Up Performance Exceeds 100 mA Per JESD 78, Class II.

SKU: RDNA-B697.1

Apple Shopping Event

Hurry and get discounts on all Apple devices up to 20%

Sale_coupon_15

₹75.00 (Inc. GST)
₹63.56 (+18% GST Extra)

In stock

For bulk orders or B2B inquiries, please contact us at: [email protected]

Compare

Add to wishlist

13 People watching this product now!

Pick up from the RoboticsDNA Store in Pune / Dunzo

To pick up today

Free

Same Day Delivery in Pune

(Mon-Sat) (Please Place Order Before 1:30 PM)

Rs. 99

via Delhivery.com (Express Mode)

Our courier will deliver to the specified address

3-5 Days

Rs. 149

via Delhivery.com (Surface Mode)

Our courier will deliver to the specified address

4-7 Days

Rs. 69

Payment Methods:

Description

You just found the perfect I2C sensor, and you want to wire up two, three, or more of them to your Arduino. When you realize “Oh no, this chip has a fixed I2C address, and from what I know about I2C; you cannot have two devices with the same address on the same SDA/SCL pins”. Are you out of luck? You would be if you don’t have this cool CJMCU TCA9548A I2C 8 Channel Multiple extensions development board.

The CJMCU TCA9548A I2C 8 Channel Multiple extensions development board is interesting in that it has an I2C address (0x70 by default) – and you basically send it a command to tell it which I2C multiplexed output you want to talk to, then you can address the board you want to address.

Specification and Features :

1-to-8 Bidirectional Translating Switches.
Supports Hot Insertion.
Low Standby Current.
1-to-8 Bidirectional Translating Switches.
Active-Low Reset Input.
Power Up With All Switch Channels Deselected.
I2C Bus and SMBus Compatible.
5-V Tolerant Inputs.
Latch-Up Performance Exceeds 100 mA Per JESD 78, Class II.

Pin Description :

Power Pins:

Vin – this is the power pin. Since the sensor chip uses 3-5 VDC. To power, the board, give it the same power as the logic level of your microcontroller – e.g. for a 5V micro like Arduino, use 5V.

GND – common ground for power and logic.

I2C Control-Side pins :

SCL – this is the I2C clock pin for the chip itself, connect to your microcontrollers I2C clock line.
SDA – this is the I2C data pin for the chip itself, connect to your microcontrollers I2C data line.
RST – this is the reset pin, for resetting the multiplexer chip. Pulled high by default, connect to ground to reset
A0 A1 A2 – these are the address selection pins for the multiplexer. By default, the multiplexer is at address 0x70 and these three pins are pulled low. Connect them to Vin to set the address to 0x71 – 0x77.
A0 is the lowest-significant bit (if it is pulled high, it will increase the address by 1).
A1 is the 2nd-lowest-significant bit (if it is pulled high, it will increase the address by 2).
A2 is the 3rd-lowest-significant bit (if it is pulled high, it will increase the address by 4).

SDx and SCx: There are 8 sets of SDx and SCx pins, from SD0/SC0 to SD7/SC7. These are the multiplexed pins. Each one is a completely separate I2C bus set. So you have 8 I2C devices with identical addresses, as long as they are on one I2C bus each.
These pins do not have any pullups installed, so if you are using a chip or breakout without I2C pull-ups be sure to add them! Nicely, you can have Vin be 3.3V and have these pins pulled up to 5V (that is, they are 5V compliant).

Sketch and Wiring Diagram:

TCA9548A Datasheet:

Adafruit TCA9548A module:

How to use video link is here: