Showing 277–286 of 286 results
Wireless Transmitter 868Mhz, Lora Shield for Leonardo,UNO, Mega2560,Duemilanove,Due
Wireless Transmitter 915Mhz, Lora Shield for Leonardo,UNO, Mega2560,Duemilanove,Due
Specifications :
- 168 dB maximum link budget.
- +20 dBm – 100 mW constant RF output vs.
- +14 dBm high-efficiency PA.
- Programmable bit rate up to 300 kbps.
- High sensitivity: down to -148 dBm.
- Bullet-proof front end: IIP3 = -12.5 dBm.
- Excellent blocking immunity.
- Low RX current of 10.3 mA, 200 nA register retention.
- Fully integrated synthesizer with a resolution of 61 Hz.
- FSK, GFSK, MSK, GMSK, LoRaTM and OOK modulation.
- Built-in bit synchronizer for clock recovery.
- Preamble detection.
- 127 dB Dynamic Range RSSI.
WS2812 1 Wire RGB LED Module Base PCB -iRobotics Not Soldered
Xbee Arduino Shield Pro
Specifications:
- Stackable design, easy to plug into the ARDUINO development board.
- Coupled with the Arduino Bluetooth Bee Bluetooth module, and other Bluetooth devices can communicate Wirelessly.
- Coupled with the XBee module, you can achieve two or more sets of communication between Arduino or Arduino and PC Communications.
- 3.3v and 5v dual power output.
- 3.3v and 5v IO compatible.
- USB 2.0 protocol.
- Bitbang mode ready.
- Easily connected to a PC via mini USB Cable.
- XBee-setting support software X-CTU.
XBee Pro S2C 63mW 802.15.4 Module without Antenna
Features:
- Data Rate: 250kbps Max
- Supply Voltage: 2.7 to 3.6 V
- Output Power: 63mW
- Supports binding and multicasting for home automation
- Operating Temperature (°C): -40 to +90
- Mesh-network topology
- 2.4 GHz Frequency
- Common XBee footprint fits Parallax XBee Adapters and the Propeller Activity Board
- Industry-leading sleep current of sub 1 µA
- Firmware upgrades via UART, SPI or over the air
Xbee S1 Pro Module
Xbee USB Adapter Base FT232RL
Specification:
- IC chip: FT232RL
- 3.3V and 5V dual power output
- 3.3V and 5V IO compatible
- USB 2.0 protocol
- BitBang mode ready
- Easily connected to a PC via mini-USB cable
- XBee-setting support software X-CTU
- Communication Protocol: UART, Bit Bang I/O, SPI
- USB Interface: Mini-B (2.54mm pitch pin header)
XBee USB Adapter FT232RL for Arduino with Cable
Specifications:
- IC chip: FT232RL
- 3.3V and 5V dual power output
- 3.3V and 5V IO compatible
- USB 2.0 protocol
- BitBang mode ready
- Easily connected to a PC via mini USB cable
- XBee-setting support software X-CTU
- Communication Protocol: UART, Bit Bang I/O, SPI
- USB Interface: Mini-B (2.54mm pitch pin header)
Xbee Zigbee Module S2c 802.15.4 2mW with Wire Antenna XB24CZ7WIT-004
Specifications:
- Integrated, Wire Antenna
- Inter-operable with other ZigBee-compliant devices
- Programmable versions with on-board microprocessor enable custom ZigBee application development
- Supports binding and multicasting for easy integration into a home automation platform
- Through-hole form factor enables flexible design
- Out-of-the-box RF communications, no configuration needed
Zigbee XBee Pro S2C 802.15.4 Module 63mW 3Km+ 3.2dBi Antenna
Features:
- Supports binding and multicasting for home automation
- Firmware upgrades via UART, SPI or over the air
- TRANSCEIVER CHIPSET: Silicon Labs EM357 SoC
- DATA RATE: 250kbps Max
- Mesh-network topology
- 2.4 GHz for worldwide deployment
- Common XBee footprint fits Parallax XBee Adapters and the Propeller Activity Board
- Industry-leading sleep current of sub 1 µA
- Firmware upgrades via UART, SPI or over the air.