Showing 25–48 of 66 results
HT12E + HT12D IC (1 PAIR)
IC ATMEGA644-20PU
Specifications:
- Advanced RISC architecture - Fully static operation
- High endurance, non-volatile memory segments
- JTAG (IEEE 1149.1 compliant) interface
- Peripheral features - Real-time Counter with separate oscillator
- Power-on reset (POR) and programmable brown-out detection
- The internal calibrated RC oscillator
- External and internal interrupt sources
- Six sleep modes - Idle, ADC noise reduction, power-save, power-down, standby and extended standby
- : 20MHz
- : 64KB
- : 4KB
- : 40Pins
- : DIP
- : 32I/O's
- : I2C, SPI, UART
- : 2.7V
- : 5.5V
- : AVR ATmega
- : ATmega64
J122G IC (Pack of 2)
LF356 IC
Features:
– Replace Expensive Hybrid and Module FET
Op Amps
– Rugged JFETs Allow Blow-Out Free Handling
Compared With MOSFET Input Devices
– Excellent for Low Noise Applications Using
Either High or Low Source Impedance—Very
Low 1/f Corner
– Offset Adjust Does Not Degrade Drift or
Common-Mode Rejection as in Most
Monolithic Amplifiers
– New Output Stage Allows Use of Large
Capacitive Loads (5,000 pF) Without Stability
Problems
– Internal Compensation and Large Differential
Input Voltage Capability
LM324 SOIC-14 Op- Amp-(Pack of 5 ICs)
Features:
- Internal frequency compensation
- Common-mode input voltage range includes ground, allowing direct sensing near ground
- Low input bias and offset parameters
- 2kV ESD Protection
- 0.8mA Typical low supply-current drain independent of supply voltage
- 3mV Typical input offset voltage
- 2nA Typical input offset current
- 20nA Typical input bias current
- 32V Differential input voltage range equal to the maximum-rated supply voltage
- 100V/mV Typical open-loop differential voltage amplification
- Green product and no Sb/Br
- Applications: Consumer Electronics, Sensing & Instrumentation, Motor Drive & Control, Test & Measurement.
LM324N IC
Specifications:
- Integrated with four Op-Amps in a single package
- Wide power supply Range
- Singe supply – 3V to 32V
- Dual supply – ±1.5V to ±16V
- Low Supply current – 700uA
- Single supply for four op-amp operation enables reliable operation
- Operating ambient temperature – 0˚C to 70˚C
- Soldering pin temperature – 260 ˚C (for 10 seconds – prescribed)
LM358P PDIP-8 High Gain Operational Amplifier (Pack of 5)
Features:
- Wide supply voltage ranges
- Low supply-current drain independent of supply voltage
- Common-mode input voltage range includes ground, allowing direct sensing near ground
- Low input bias and offset parameters
- Internal frequency compensation
- Applications: Sensing & Instrumentation, Communications & Networking, Audio.
M74HC221B1 ST Micro TTL IC Dual Multivibrator Plastic 74HC221
MAX232CPE DIP IC
MAX232CSE SOIC-Narrow-16 RS-232 Interface IC (Pack of 2 ICs)
Features:
- Operates With Single 5-V Power Supply
- LinBiCMOS Process Technology
- Two Drivers and Two Receivers
- ±30-V Input Levels
- Low Supply Current . . . 8 mA Typical
- Meets or Exceeds TIA/EIA-232-F and ITURecommendation V.28
- Designed to be Interchangeable WithMaxim MAX232
- ESD Protection Exceeds JESD 22– 2000-V Human-Body Model (A114-A)
- Applications: TIA/EIA-232-F, Battery-Powered Systems Terminals, Modems.
MAX232N IC
Specifications:
- Meets or Exceeds TIA/EIA-232-F and ITU Recommendation V.28
- Operates From a Single 5-V Power Supply With 1.0-µF Charge-Pump Capacitors
- Operates up to 120 kbit/s
- Two Drivers and Two Receivers
- ±30-V Input Levels
- Low Supply Current: 8 mA Typical
- ESD Protection Exceeds JESD 22
- 2000-V Human-Body Model(A114-A)
- Upgrade With Improved ESD (15-kV HBM) and 0.1-µF Charge-Pump Capacitors is Available With the MAX202 Device
MAX485CPA PDIP-8 Interface ICs
MAX485CSA SO-8 Transceiver Interface IC
MAX7219CNG LED Driver Dip Ic
Specifications:
♦ 10MHz Serial Interface
♦ Individual LED Segment Control
♦ Decode/No-Decode Digit Selection
♦ 150µA Low-Power Shutdown (Data Retained)
♦ Digital and Analog Brightness Control
♦ Display Blanked on Power-Up
♦ Drive Common-Cathode LED Display
♦ Slew-Rate Limited Segment Drivers
for Lower EMI (MAX7221)
♦ SPI, QSPI, MICROWIRE Serial Interface (MAX7221)
♦ 24-Pin DIP and SO Packages
MC34063API PDIP-8 Switching Buck Voltage Regulators (Pack of 2 ICs)
Features:
- Adjustable output voltage range from 1.25V to 40V
- Wide input voltage range from 3V to 40V
- High output switch current up to 1.5A
- Oscillator frequency up to 100KHz
- The precision internal reference is 2%
- Short circuit current limiting
- Low standby current
- Operating temperature range 0°C to 70°C
MCP73831T-2ACI/OT SMD IC (2 Pcs)
Specifications:
- Maximum Operating Temperature:+85 °C
- Length:3.1mm
- Brand: Microchip
- Package-Type: SOT-23
- Mounting Type: Surface Mount
- Minimum Operating Temperature: -40 °C
- Pin Count: 5
- Battery Type: Lithium-Ion, Lithium-Polymer
- Dimensions: 3.1 x 1.8 x 1.3mm
- Typical Operating Supply Voltage: 3.75 → 6 V
MD1802FX B651 IC
MD1803DFX B702 IC
MOC3021 809Q IC
NE555 SOIC-8 Timer (Pack of 5 ICs)
NXP P89V51RD2FN IC
Features:
- 80C51 Central Processing Unit
- 5 V Operating voltage from 0 to 40 MHz
- 64 kB of on-chip Flash program memory with ISP (In-System Programming) and IAP (In-Application Programming)
- Supports 12-clock (default) or 6-clock mode selection via software or ISP
- SPI (Serial Peripheral Interface) and enhanced UART
- PCA (Programmable Counter Array) with PWM and Capture/Compare functions
- Four 8-bit I/O ports with three high-current Port 1 pins (16 mA each)
- Three 16-bit timers/counters
- Programmable Watchdog timer (WDT)
- Eight interrupt sources with four priority levels
- Second DPTR register
- Low EMI mode (ALE inhibit)
- TTL- and CMOS-compatible logic levels